|
 | | ROB00199 | Display AD ( black - white display ) | | |
| | ||||||||
| The universal i2C Display AD interface with a black and white display supports about 40 functions that you can use in programming different interfaces (Arduino, Raspberry, micro: bit, ...). The interface is Display AD is Arduino UNO compatible and uses ATMEGA328 microprocessor at 16 Mhz. To allow you to program the interface, we have installed a programming | | connector. The interface can be programmed as an Arduino UNO or via a programmer. The interface uses a screen with a resolution of 84x48 pixels for graphic or textual display. For the audio output, a 0.5W speaker with a volume control is installed and connected to pin 2 of the microcontroller. To receive data from different sensors, three input connectors | | are used which are connected to pins A1, A2, A3, and two I2C connectors (5V and 3.3V). Sensors with a signal up to 9V can be connected to the inputs. To power the sensor, the interface has two outputs with a power supply of 3.3V and 5V. A 9V battery (or a 5V connector on the UNO / MEGA interface) or a 5V USB adapter can be used to power the interface. | |
|
|
|
|
|
 | | ROB00154 | Uno-F5 board ( Arduino UNO - fischertehnik ) power conn. 5.2 x 2.1 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8 | | x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00155 | Uno-F5 board ( Arduino UNO - fischertehnik ) power conn. 3.5 x 1.3 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8 | | x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00160 | Mega-F5 board ( Arduino MEGA - fischertehnik ) power conn. 5.2 x 2.1 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage), | | 6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00162 | Mega-F5 board ( Arduino MEGA - fischertehnik ) power conn. 3.5 x 1.3 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage), | | 6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00191 | Uno-T5 board ( Arduino UNO - fischertehnik ) power conn. 5.2 x 2.1 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8 | | x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX.9V. | |
|
|
|
|
|
|
 | | ROB00192 | Uno-T5 board ( Arduino UNO - fischertehnik ) power conn. 3.5 x 1.3 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 8x OUTPUT - max 600 mA for each output (depending on input voltage), 4 x DC motor or 8 | | x LED, 8 x INPUTS ( outputs ) - 2 x digital, 6 x analog, TX + RX, I2C, , 2 x SERVO ( 5V ). Board for Arduino UNO. All inputs are with PULL UP resistors ( HIGH state ). Max. VOLTAGE on INPUTS MAX.9V. | |
|
|
|
|
|
|
 | | ROB00195 | Mega-T5 board ( Arduino MEGA - fischertehnik ) power conn. 5.2 x 2.1 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage), | | 6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00196 | Mega-T5 board ( Arduino MEGA - fischertehnik ) power conn. 3.5 x 1.3 mm | | |
| | ||||||||
Discount for bigger quantity. |
|
|
| Board for Arduino MEGA (256). Specification: Power DC connector 6 - 9V, 9V battery conn., output 5v and 3.3V, conn. for wireles modul NRF24L01, 12x OUTPUT - max 600 mA for each output (depending on input voltage), | | 6 x DC motor ( 5 x PWM ) or 12 x LED, 12 x INPUTS ( outputs ) - 12 x analog/digital, TX + RX, I2C, 2 x SERVO ( 5V ). All inputs are with PULL UP resistors ( HIGH state ). VOLTAGE on INPUTS MAX. 9V. | |
|
|
|
|
|
|
 | | ROB00172 | X holder V2 for Arduino UNO / MEGA (3D print) | | |
| | |
|
|